Protective Case Support Cooling Fan + Touch Pen Kit For Raspberry
ShopCalifornia
ShopCalifornia’s Super Sale is Back!
Introduction :
Sometimes you use the the Raspberry Pi with 3.5 inch touchscreen , but sometime you don't use them together. In this situation , you need a case which both suitable for Raspberry Pi alone or with 3.5 inch touchscreen. This is the reason we provide this new case -- for the people use 3.5 inch screen more convenient: When you use the touchscreen , just remove the cover board and fan; When you don't use the touchscreen , you can use the cover and fan , which become a normal case.
Please note that you can't use the 3.5 inch touchscreen and cooling fan at the sametime !
Features :
1. One case for two use :
1). This case suport install 3.5 inch touchscreen , and need to remove the cover board and can't use the fan in this using way.
2). When you don't use the 3.5 inch touchscreen , it is a general case with cooling fan.
2. Full access for Raspberry Pi :
We leave every hole for SD card , HDMI , AV , Ethernet , USB , POE , Camera , MIPI DSI ports.
3. Support cooling fan :
You can install the cooling fan on the cover board , which make the best heat dissipation and extend the using life of Raspberry Pi.
( You can't use the 3.5 inch touchscreen and cooling fan at the sametime ! )
4. Hange hole on the bottom :
We make 2 hole on the bottom so that you can hange the case on the wall or something else .
This design is very convenient when using the 3.5 inch touchscreen.
-480×320 pixel resolution, better display.
-Driver provided (works with custom Raspbian directly).
-Supports any revision of Rasp Pi (directly-pluggable).
-Designed for Raspberry Pi, an ideal alternative solution for monitor.
-Support software keyboard (system interaction without keyboard/mouse).
-Provides the best available protection/accessibility for Model B
How to install the 3.5 inch touchscreen :
1). Install the Raspberry Pi on the base board
2). Please stick the pad on the back of 3.5 inch touchscreen , then insert the 3.5 inch touchscreen on Raspberry Pi by GPIO pin correctly ( don't be malposed )
3). Install the cover board
Parameter:
LCD Type | TFT |
---|---|
LCD Interface | SPI |
Touch Screen Type | Resistive |
Touch Screen Controller | XPT2046 |
Colors | 65536 |
Backlight | LED |
Resolution | 320*480 (Pixel) |
Aspect Ratio | 8:5 |
Power Consumption | TBD |
Backlight Current | TBD |
Operating Temp. (Centigrade) | TBD |
Interface Definition:
PIN NO. | SYMBOL | DESCRIPTION |
---|---|---|
1, 17 | 3.3V | Power positive (3.3V power input) |
2, 4 | 5V | Power positive (5V power input) |
3, 5, 7, 8, 10, 12, 13, 15, 16 | NC | NC |
6, 9, 14, 20, 25 | GND | Ground |
11 | TP_IRQ | Touch Panel interrupt, low level while the Touch Panel detects touching |
18 | LCD_RS | Instruction/Data Register selection |
19 | LCD_SI / TP_SI | SPI data input of LCD/Touch Panel |
21 | TP_SO | SPI data output of Touch Panel |
22 | RST | Reset |
23 | LCD_SCK / TP_SCK | SPI clock of LCD/Touch Panel |
24 | LCD_CS | LCD chip selection, low active |
26 | TP_CS |
Touch Panel chip selection, low active |
About the system of 3.5 touch screen
The touch screen need to configure the driver for touch function , otherwise you can not use it by your own system.
Here we provide the method to configure for Raspbian system :
Step 1: Download the Raspbian IMG
Step 2: Burn the system image
If you don't know how to do that,you can refer to the Raspberry Pi office tutorial
Step 3: Open terminal(SSH) and install the driver on RaspberryPi
(tested on RaspberryPi 3B+,3B,2B,2B+,1B,ZERO)
Drive File:
sudo rm -rf LCD-show
git clone https://github.com/goodtft/LCD-show.git
chmod -R 755 LCD-show
cd LCD-show/
sudo ./LCD35-show
Make sure your RPI connects to the internet then wait a few minutes, when the system reboot ok, you can see that.
You can also download the system image which we already configured well by following links :
1. for Raspberry Pi 3 :
https://mega.nz/#!vc4zjRRR!A9OMnL4tVjXUwH5Tt4T0ES2WxJyA4DGUg-gid_JHQVA
2. for Raspberry Pi 3 Modle B+ :
https://mega.nz/#!SQRl3BSS!ZwuE1VsoQSpUwHm2sa6zk1GPsU36M7793Q35NvdSYVY
or refer to configure it by this link :
https://github.com/goodtft/LCD-show
Package included:
1 x 3.5 inch Touch Screen
1 x Protective Case
1 x Touch Pen
THIS PRODUCT IS A LIMITED PRODUCTION OF SHOPCALIFORNIA AND IT’S NOT AVAILABLE IN STORES. IT WILL SELL OUT FAST!
Click ADD TO CART to Order Yours Now!
WE DONATE A PORTION OF OUR PROFITS TO ENVIRONMENTAL CHARITIES
Every order you make with us benefits the environment. Thank you for protecting our seas, forests & wildlife with us!
In Stock: Leaves
warehouse in 1 to 2 days
Free Worldwide
Shipping Available
Contact Options: Email: support@dublintrends.com (Best Option) Phone Number: 353 76 670 1268 / Dublin Address: 13 Adelaide Road, Dublin, Ireland D02 P950 / USA Head Office Address: 2232 Dell Range Blvd, Suite 245, Cheyenne, WY, USA 82009